运用STM32来访问I2C接口的铁电存储器，FM24CL16，2K字节
=================================
I2C的引脚装备：
/*ConfigureI2C1pins:SCLandSDA*/
GPIO_InitStructure.GPIO_Pin=GPIO_Pin_6|GPIO_Pin_7;
GPIO_InitStructure.GPIO_Speed=GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode=GPIO_Mode_Out_OD;
GPIO_Init(GPIOB,&GPIO_InitStructure);
=================================
/*******************************************************************************
*FileName:i2c_fram.h
*Author:MCDApplicationTeam
*Version:V2.0.1
*Date:06/13/2008
*Description:Headerfori2c_ee.cmodule
*******************************************************************************/
/*Definetopreventrecursiveinclusion————————————*/
#ifndef__I2C_FRAM_H
#define__I2C_FRAM_H
/*Includes——————————————————————*/
#include”stm32f10x_lib.h”
/*Exportedtypes————————————————————*/
/*Exportedconstants——————————————————–*/
/*Exportedmacro————————————————————*/
/*Exportedfunctions——————————————————-*/
boolI2C_FRAM_BufferWrite(u8*pBuffer,u16WriteAddr,u16NumByteToWrite);
boolI2C_FRAM_BufferRead(u8*pBuffer,u16ReadAddr,u16NumByteToRead);
#endif/*__I2C_FRAM_H*/
=================================
/*******************************************************************************
*FileName:i2c_fram.c
*Author:Appcat
*Version:V0.0.1
*Date:07/11/2009
*Description:Thisfileprovidesasetoffunctionsneededtomanagethe
*communicationbetweenI2CperipheralandI2CFM24CL16FRAM.
*******************************************************************************/
/*Includes——————————————————————*/
#include”i2c_fram.h”
/*Privatetypedef———————————————————–*/
/*Privatedefine————————————————————*/
#defineI2C_Speed100000
#defineI2C1_SLAVE_ADDRESS70xA0
#defineI2C_PageSize256
#defineSCL_HGPIOB->BSRR=GPIO_Pin_6
#defineSCL_LGPIOB->BRR=GPIO_Pin_6
#defineSDA_HGPIOB->BSRR=GPIO_Pin_7
#defineSDA_LGPIOB->BRR=GPIO_Pin_7
#defineSCL_readGPIOB->IDR&GPIO_Pin_6
#defineSDA_readGPIOB->IDR&GPIO_Pin_7
/*Privatemacro————————————————————-*/
/*Privatevariables———————————————————*/
vu8FRAM_ADDRESS;
/*Privatefunctionprototypes———————————————–*/
/**/
voidI2C_delay(void)
{
u8i=150;//这儿能够优化速度 ，经测验最低到5还能写入
while(i)
{
i–;
}
}
boolI2C_Start(void)
{
SDA_H;
SCL_H;
I2C_delay();
if(!SDA_read)returnFALSE; //SDA线为低电平则总线忙,退出
SDA_L;
I2C_delay();
if(SDA_read)returnFALSE; //SDA线为高电平则总线犯错,退出
SDA_L;
I2C_delay();
returnTRUE;
}
voidI2C_Stop(void)
{
SCL_L;
I2C_delay();
SDA_L;
I2C_delay();
SCL_H;
I2C_delay();
SDA_H;
I2C_delay();
}
voidI2C_Ack(void)
{
SCL_L;
I2C_delay();
SDA_L;
I2C_delay();
SCL_H;
I2C_delay();
SCL_L;
I2C_delay();
}
voidI2C_NoAck(void)
{
SCL_L;
I2C_delay();
SDA_H;
I2C_delay();
SCL_H;
I2C_delay();
SCL_L;
I2C_delay();
}
boolI2C_WaitAck(void) //回来为:=1有ACK,=0无ACK
{
SCL_L;
I2C_delay();
SDA_H;
I2C_delay();
SCL_H;
I2C_delay();
if(SDA_read)
{
SCL_L;
returnFALSE;
}
SCL_L;
returnTRUE;
}
voidI2C_SendByte(u8SendByte)//数据从高位到低位//
{
u8i=8;
while(i–)
{
SCL_L;
I2C_delay();
if(SendByte&0x80)
SDA_H;
else
SDA_L;
SendByte<<=1;
I2C_delay();
SCL_H;
I2C_delay();
}
SCL_L;
}
u8I2C_ReceiveByte(void)//数据从高位到低位//
{
u8i=8;
u8ReceiveByte=0;
SDA_H;
while(i–)
{
ReceiveByte<<=1;
SCL_L;
I2C_delay();
SCL_H;
I2C_delay();
if(SDA_read)
{
ReceiveByte|=0x01;
}
}
SCL_L;
returnReceiveByte;
}
boolI2C_FRAM_BufferWrite(u8*pBuffer,u16WriteAddr,u16NumByteToWrite)
{
u8Addr=0,count=0;
Addr=WriteAddr/I2C_PageSize;
count=WriteAddr%I2C_PageSize;
Addr=Addr<<1;
Addr=Addr&0x0F;
FRAM_ADDRESS=I2C1_SLAVE_ADDRESS7|Addr;
if(!I2C_Start())returnFALSE;
I2C_SendByte(FRAM_ADDRESS);//设置器材地址+段地址
if(!I2C_WaitAck())
{
I2C_Stop();
returnFALSE;
}
I2C_SendByte(count);//设置段内地址
I2C_WaitAck();
while(NumByteToWrite–)
{
I2C_SendByte(*pBuffer);
I2C_WaitAck();
pBuffer++;
}
I2C_Stop();
//留意：由于这儿要等候EEPROM写完，能够选用查询或延时方法(10ms)
//Systick_Delay_1ms(10);
returnTRUE;
}
//读出1串数据
boolI2C_FRAM_BufferRead(u8*pBuffer,u16WriteAddr,u16NumByteToRead)
{
u8Addr=0,count=0;
Addr=WriteAddr/I2C_PageSize;
count=WriteAddr%I2C_PageSize;
Addr=Addr<<1;
Addr=Addr&0x0F;
FRAM_ADDRESS=I2C1_SLAVE_ADDRESS7|Addr;
if(!I2C_Start())returnFALSE;
I2C_SendByte(FRAM_ADDRESS);//设置器材地址+段地址
if(!I2C_WaitAck())
{
I2C_Stop();
returnFALSE;
}
I2C_SendByte(count);//设置低开始地址
I2C_WaitAck();
I2C_Start();
I2C_SendByte(FRAM_ADDRESS|0x01);
I2C_WaitAck();
while(NumByteToRead)
{
*pBuffer=I2C_ReceiveByte();
if(NumByteToRead==1)I2C_NoAck();
elseI2C_Ack();
pBuffer++;
NumByteToRead–;
}
I2C_Stop();
returnTRUE;
}
=================================
