您的位置 首页 培训

stm32之i2C硬件驱动ht16c22

2020年9月18日 13:17 阅读(416)

使用硬件i2c，驱动ht16c22，程序不稳定是肯定的，还是贴出来吧，项目中最好不要用。文件i2c.h内容:#ifndef_STM32F103_I2C_H_#define_ST…

运用硬件i2c，驱动ht16c22，程序不稳定是必定的，仍是贴出来吧，项目中最好不要用。

文件i2c.h内容:


#ifndef _STM32F103_I2C_H_
#define _STM32F103_I2C_H_
#include “stm32f10x.h”
#define SlaveAddress 0x7e //0x7e
//#define ModeSet 0b10001100 //80Hz,turn on sys and LCD bias,1/3 bias
#define ModeSet 0x8C //80Hz,turn on sys and LCD bias,1/3 bias
//#define VlcdAdjust 0b01111111 //Vlcd=0.6VDD,Seg Pin,enable internal voltage
#define VlcdAdjust 0x70 //0x7F –Vlcd=0.6VDD,Seg Pin,enable internal voltage
//#define Blink 0b11000000 //封闭闪耀
#define Blink 0xC0 //封闭闪耀


void LCD_I2C_config(void);
void I2C_Write(unsigned int device_id, unsigned int register_id, unsigned int data);
unsigned char I2C_Read(unsigned int device_id, unsigned int register_id);


void ht16c22_init(void );


unsigned char I2C_ht16c22_Read(unsigned int pBuffer, unsigned int ReadAddr);
void I2C_ht16c22_Write(unsigned int device_id, unsigned int register_id);


#endif




i2c.c文件内容为:








#include “xx.h”


static void I2C_Config(void)
{
GPIO_InitTypeDef GPIO_InitStructure;


RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C2, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB ,ENABLE);


/*config I2C2 SCL PB10*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;


GPIO_Init(GPIOB, &GPIO_InitStructure);
/*config I2C2 SDA PB11 */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;


GPIO_Init(GPIOB, &GPIO_InitStructure);
}


void LCD_I2C_config(void)
{
I2C_InitTypeDef I2C_InitStructure;
I2C_Config();
I2C_DeInit(I2C2);


I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;
I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_16_9;//I2C_DutyCycle_2//I2C_DutyCycle_16_9
I2C_InitStructure.I2C_OwnAddress1 = 0x0A; //0x0A//0xA0
I2C_InitStructure.I2C_Ack = I2C_Ack_Enable;
I2C_InitStructure.I2C_ClockSpeed = 10000;//10KHZ的速率
I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;


I2C_Init(I2C2, &I2C_InitStructure);


I2C_Cmd(I2C2, ENABLE);
}


int I2C_FLAG_BUSY_write = 0;
int I2C_EVENT_MASTER_MODE_SELECT_write = 0 ;
int I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED_write = 0 ;
int I2C_EVENT_MASTER_BYTE_TRANSMITTED_write = 0 ;


void I2C_Write(unsigned int device_id, unsigned int register_id, unsigned int data)
{
int i = 0;
while(I2C_GetFlagStatus(I2C2, I2C_FLAG_BUSY))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_GenerateSTART(I2C2, ENABLE);


while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_MODE_SELECT))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_Send7bitAddress(I2C2, device_id, I2C_Direction_Transmitter);


while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_SendData(I2C2, register_id);


while(! I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_TRANSMITTED))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_SendData(I2C2, data);


while(! I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_TRANSMITTED))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_GenerateSTOP(I2C2, ENABLE);
}


void ht16c22_init()
{
LCD_I2C_config();
I2C_ht16c22_Write(SlaveAddress,ModeSet);
I2C_ht16c22_Write(SlaveAddress,VlcdAdjust);
I2C_ht16c22_Write(SlaveAddress,Blink);


I2C_Write(SlaveAddress,0x00,0x00);
I2C_Write(SlaveAddress,0x01,0x00);
I2C_Write(SlaveAddress,0x02,0x00);
I2C_Write(SlaveAddress,0x03,0x00);
I2C_Write(SlaveAddress,0x04,0x00);
I2C_Write(SlaveAddress,0x05,0x00);
I2C_Write(SlaveAddress,0x06,0x00);
I2C_Write(SlaveAddress,0x07,0x00);
I2C_Write(SlaveAddress,0x08,0x00);
I2C_Write(SlaveAddress,0x09,0x00);
I2C_Write(SlaveAddress,0x0A,0x00);
I2C_Write(SlaveAddress,0x0B,0x00);
I2C_Write(SlaveAddress,0x0C,0x00);
I2C_Write(SlaveAddress,0x0D,0x00);
I2C_Write(SlaveAddress,0x0E,0x00);
I2C_Write(SlaveAddress,0x0F,0x00);
I2C_Write(SlaveAddress,0x10,0x00);
I2C_Write(SlaveAddress,0x11,0x00);
I2C_Write(SlaveAddress,0x12,0x00);
I2C_Write(SlaveAddress,0x13,0x00);
I2C_Write(SlaveAddress,0x14,0x00);
I2C_Write(SlaveAddress,0x15,0x00);
I2C_Write(SlaveAddress,0x16,0x00);
I2C_Write(SlaveAddress,0x17,0x00);
I2C_Write(SlaveAddress,0x17,0x00);
I2C_Write(SlaveAddress,0x18,0x00);
I2C_Write(SlaveAddress,0x19,0x00);
I2C_Write(SlaveAddress,0x1A,0x00);
I2C_Write(SlaveAddress,0x1B,0x00);
I2C_Write(SlaveAddress,0x1C,0x00);
I2C_Write(SlaveAddress,0x1D,0x00);
I2C_Write(SlaveAddress,0x1E,0x00);
I2C_Write(SlaveAddress,0x1F,0x00);
I2C_Write(SlaveAddress,0x20,0x00);
I2C_Write(SlaveAddress,0x21,0x00);


// I2C_Write(SlaveAddress,0x00,0xFF);
// I2C_Write(SlaveAddress,0x01,0xFF);
// I2C_Write(SlaveAddress,0x02,0xFF);
// I2C_Write(SlaveAddress,0x03,0xFF);
// I2C_Write(SlaveAddress,0x04,0xFF);
// I2C_Write(SlaveAddress,0x05,0xFF);
// I2C_Write(SlaveAddress,0x06,0xFF);
// I2C_Write(SlaveAddress,0x07,0xFF);
// I2C_Write(SlaveAddress,0x08,0xFF);
// I2C_Write(SlaveAddress,0x09,0xFF);
// I2C_Write(SlaveAddress,0x0A,0xFF);
// I2C_Write(SlaveAddress,0x0B,0xFF);
// I2C_Write(SlaveAddress,0x0C,0xFF);
// I2C_Write(SlaveAddress,0x0D,0xFF);
// I2C_Write(SlaveAddress,0x0E,0xFF);
// I2C_Write(SlaveAddress,0x0F,0xFF);
// I2C_Write(SlaveAddress,0x10,0xFF);
// I2C_Write(SlaveAddress,0x11,0xFF);
// I2C_Write(SlaveAddress,0x12,0xFF);
// I2C_Write(SlaveAddress,0x13,0xFF);
// I2C_Write(SlaveAddress,0x14,0xFF);
// I2C_Write(SlaveAddress,0x15,0xFF);
// I2C_Write(SlaveAddress,0x16,0xFF);
// I2C_Write(SlaveAddress,0x17,0xFF);
// I2C_Write(SlaveAddress,0x17,0xFF);
// I2C_Write(SlaveAddress,0x18,0xFF);
// I2C_Write(SlaveAddress,0x19,0xFF);
// I2C_Write(SlaveAddress,0x1A,0xFF);
// I2C_Write(SlaveAddress,0x1B,0xFF);
// I2C_Write(SlaveAddress,0x1C,0x00);
// I2C_Write(SlaveAddress,0x1D,0x00);
// I2C_Write(SlaveAddress,0x1E,0x00);
// I2C_Write(SlaveAddress,0x1F,0x00);
// I2C_Write(SlaveAddress,0x20,0x00);
// I2C_Write(SlaveAddress,0x21,0x00
// I2C_Write(SlaveAddress,0x05,0x0F);
// temp = I2C_ht16c22_Read(SlaveAddress,0x05);
// I2C_Write(SlaveAddress,0x05,(0x10) | temp);


// temp = I2C_ht16c22_Read(SlaveAddress,0x05);
// printf(“temp = %d\r\n” ,temp);
// I2C_Write(SlaveAddress,0x05,0xE0 | temp);
//
// temp = I2C_ht16c22_Read(SlaveAddress,0x06);
// I2C_Write(SlaveAddress,0x06,0x0F | temp);


// I2C_ht16c22_Write(SlaveAddress,0x80,0x03,0xff);


// I2C_Write(SlaveAddress,0x0A,0xFF);
// I2C_Write(SlaveAddress,0x00,0xFF);
// I2C_Write(SlaveAddress,0x01,0xFF);
// I2C_Write(SlaveAddress,0x02,0xFF);
//
// I2C_Write(SlaveAddress,0x03,0xFF);
// I2C_Write(SlaveAddress,0x04,0xFF);
// I2C_Write(SlaveAddress,0x05,0xFF);
// I2C_Write(SlaveAddress,0x06,0xFF);
//
// I2C_Write(SlaveAddress,0x07,0xFF);
// I2C_Write(SlaveAddress,0x08,0xFF);
// I2C_Write(SlaveAddress,0x09,0xFF);
//
// I2C_Write(SlaveAddress,0x0A,0xFF);
// I2C_Write(SlaveAddress,0x0B,0xFF);
// I2C_Write(SlaveAddress,0x0C,0xFF);
// I2C_Write(SlaveAddress,0x0D,0xFF);
//
//
// I2C_Write(SlaveAddress,0x0E,0xFF);
// I2C_Write(SlaveAddress,0x0F,0xFF);
// I2C_Write(SlaveAddress,0x10,0xFF);
// I2C_Write(SlaveAddress,0x11,0xFF);
//
// I2C_Write(SlaveAddress,0x12,0xFF);
// I2C_Write(SlaveAddress,0x13,0xFF);
// I2C_Write(SlaveAddress,0x14,0xFF);
// I2C_Write(SlaveAddress,0x15,0xFF);


}


void I2C_ht16c22_Write(unsigned int device_id, unsigned int register_id)
{


while(I2C_GetFlagStatus(I2C2, I2C_FLAG_BUSY)); // Added by Najoua 27/08/2008


I2C_GenerateSTART(I2C2, ENABLE);


while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_MODE_SELECT));


I2C_Send7bitAddress(I2C2, device_id, I2C_Direction_Transmitter);


while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED));


I2C_SendData(I2C2, register_id);


while(! I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_TRANSMITTED))
;
I2C_GenerateSTOP(I2C2, ENABLE);
}


int I2C_FLAG_BUSY_read = 0;
int I2C_EVENT_MASTER_MODE_SELECT_read_1 = 0 ;
int I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED_read_1 = 0 ;
int I2C_EVENT_MASTER_BYTE_TRANSMITTED_read = 0 ;
int I2C_EVENT_MASTER_MODE_SELECT_read_2 = 0 ;
int I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED_read_2 = 0 ;
int I2C_EVENT_MASTER_BYTE_RECEIVED_read = 0;


unsigned char I2C_ht16c22_Read(unsigned int pBuffer, unsigned int ReadAddr)
{
unsigned char temp;
int i = 0;


while(I2C_GetFlagStatus(I2C2, I2C_FLAG_BUSY))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}
I2C_GenerateSTART(I2C2, ENABLE);


while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_MODE_SELECT))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_Send7bitAddress(I2C2, pBuffer, I2C_Direction_Transmitter);


while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_Cmd(I2C2, ENABLE);


I2C_SendData(I2C2, ReadAddr);


/* Test on EV8 and clear it */
while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_TRANSMITTED))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_GenerateSTART(I2C2, ENABLE);


while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_MODE_SELECT))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}


I2C_Send7bitAddress(I2C2, pBuffer, I2C_Direction_Receiver);


while(!I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED))
{
;
}


I2C_AcknowledgeConfig(I2C2, DISABLE);
I2C_GenerateSTOP(I2C2, ENABLE);
while(!(I2C_CheckEvent(I2C2, I2C_EVENT_MASTER_BYTE_RECEIVED)))
{
if(i == 65536)
{
debug(“—-i2c dead——–\r\n”);
i = 0;
break;
}
;
}
temp = I2C_ReceiveData(I2C2);
I2C_AcknowledgeConfig(I2C2, ENABLE);


return temp;


}


好了，硬件i2c就到这儿就完毕吧。



	


	
		

			声明：本文内容来自网络转载或用户投稿，文章版权归原作者和原出处所有。文中观点，不代表本站立场。若有侵权请联系本站删除（kf@86ic.com）https://www.86ic.net/changshang/peixun/252301.html		


	
	


				

								
				
					 1赞				

					

		


	


	

		


			标签:    				
			
		
	

		
	







		

			
为您推荐

			

														

						
							

																													
							

									
						
安森美与伍尔特电子携手升级高精度电力电子应用虚拟设计

					

														

						
							

																													
							

									
						
2025年6月13日-15日甘肃（兰州）暖通展震撼来袭

					

														

						
							

																													
							

									
						
小漫电子经销移远EC800K物联网4G全网通CAT1网络远程控制DTU模块ASR芯片模组 EC800KCNCC-I01-SNNSA

					

														

						
							

																													
							

									
						
使用差分来测试开关模式电源

					

														

						
							

																													
							

									
						
RECOM 首次推出具备 2MOPP/250 VAC 医疗级、宽输入 DC/DC 转换器

					

														

						
							

																													
							

									
						
如何打造“不一样”的电源管理器件？

					

							

		


			



	





		


	

	
	


	






		

		
			
			联系我们
		
	    

		    

		    	

			        
联系我们


			        
			    				        	
在线咨询: QQ交谈

			        
			        			       		
邮箱: kf@86ic.com
	
			        
			        		    	

		        		        
		    

		
				
	

	
		
	

		
			
			关注微信
				
	    

		    

		        微信扫一扫关注我们
		        
微信扫一扫关注我们

		        
		    

		
		
	

	
	
		

		
			
			返回顶部