您的位置 首页 新品

ARM移植之BootLoader(3)

3.2Bootloader拷贝配置为从NANDFLASH启动,需要将NANDFLASH中的vivi代码copy到RAM中:#ifdefCONFIG_S3C2410_NAND_BOOTblcopy_m.

3.2Bootloader复制

  装备为从NAND FLASH发动,需要将NAND FLASH中的vivi代码copy到RAM中:

#ifdef CONFIG_S3C2410_NAND_BOOT
bl copy_myself

@ jump to ram
ldr r1, =on_the_ram
add pc, r1, #0
nop
nop
1: b 1b @ infinite loop

#ifdef CONFIG_S3C2410_NAND_BOOT
@
@ copy_myself: copy vivi to ram
@
copy_myself:
mov r10, lr

@ reset NAND
mov r1, #NAND_CTL_BASE
ldr r2, =0xf830 @ initial value
str r2, [r1, #oNFCONF]
ldr r2, [r1, #oNFCONF]
bic r2, r2, #0x800 @ enable chip
str r2, [r1, #oNFCONF]
mov r2, #0xff @ RESET command
strb r2, [r1, #oNFCMD]
mov r3, #0 @ wait
1: add r3, r3, #0x1
cmp r3, #0xa
blt 1b
2: ldr r2, [r1, #oNFSTAT] @ wait ready
tst r2, #0x1
beq 2b
ldr r2, [r1, #oNFCONF]
orr r2, r2, #0x800 @ disable chip
str r2, [r1, #oNFCONF]

@ get read to call C functions (for nand_read())
ldr sp, DW_STACK_START @ setup stack pointer
mov fp, #0 @ no previous frame, so fp=0

@ copy vivi to RAM
ldr r0, =VIVI_RAM_BASE
mov r1, #0x0
mov r2, #0x20000
bl nand_read_ll

tst r0, #0x0
beq ok_nand_read
#ifdef CONFIG_DEBUG_LL
bad_nand_read:
ldr r0, STR_FAIL
ldr r1, SerBase
bl PrintWord
1: b 1b @ infinite loop
#endif

ok_nand_read:
#ifdef CONFIG_DEBUG_LL
ldr r0, STR_OK
ldr r1, SerBase
bl PrintWord
#endif

@ verify
mov r0, #0
ldr r1, =0x33f00000
mov r2, #0x400 @ 4 bytes * 1024 = 4K-bytes
go_next:
ldr r3, [r0], #4
ldr r4, [r1], #4
teq r3, r4
bne notmatch
subs r2, r2, #4
beq done_nand_read
bne go_next
notmatch:
#ifdef CONFIG_DEBUG_LL
sub r0, r0, #4
ldr r1, SerBase
bl PrintHexWord
ldr r0, STR_FAIL
ldr r1, SerBase
bl PrintWord
#endif
1: b 1b
done_nand_read:

#ifdef CONFIG_DEBUG_LL
ldr r0, STR_OK
ldr r1, SerBase
bl PrintWord
#endif

mov pc, r10

@ clear memory
@ r0: start address
@ r1: length
mem_clear:
mov r2, #0
mov r3, r2
mov r4, r2
mov r5, r2
mov r6, r2
mov r7, r2
mov r8, r2
mov r9, r2

clear_loop:
stmia r0!, {r2-r9}
subs r1, r1, #(8 * 4)
bne clear_loop

mov pc, lr

#endif @ CONFIG_S3C2410_NAND_BOOT

  3.3进入C代码

  首先要设置仓库指针sp,仓库指针的设置是为了履行C言语代码作好预备。设置好仓库后,调用C言语的main函数:

@ get read to call C functions
ldr sp, DW_STACK_START @ setup stack pointer
mov fp, #0 @ no previous frame, so fp=0
mov a2, #0 @ set argv to NULL

bl main @ call main

mov pc, #FLASH_BASE @ otherwise, reboot

声明:本文内容来自网络转载或用户投稿,文章版权归原作者和原出处所有。文中观点,不代表本站立场。若有侵权请联系本站删除(kf@86ic.com)https://www.86ic.net/xinpin/275765.html

为您推荐

联系我们

联系我们

在线咨询: QQ交谈

邮箱: kf@86ic.com

关注微信
微信扫一扫关注我们

微信扫一扫关注我们

返回顶部