STM32下关于串口的固件库写得适当好了，以下仅仅本文对串口库的一点点封装：
/*HKY_uart.h*/#ifndef _HKY_UART_H_#define _HKY_UART_H_#include "stm32f10x_lib.h"//#include "platform_config.h"#define GPIO_RTSPin GPIO_Pin_1#define GPIO_CTSPin GPIO_Pin_0#define GPIO_TxPin GPIO_Pin_2#define GPIO_RxPin GPIO_Pin_3void USART2_Configuration(void);int USART_sendBuf(USART_TypeDef* USARTx, u8 *buf, u32 len);int USART_recvBuf(USART_TypeDef* USARTx, u8 *buf, u32 len);#endif //_HKY_UART_H_
/*HKY_uart.c*/#include "HKY_uart.h"/* --------------------------------------------------------------------------*// * @Brief: USART2_Configuration *//* --------------------------------------------------------------------------*/void USART2_Configuration(void){USART_InitTypeDef USART_InitStructure;GPIO_InitTypeDef GPIO_InitStructure;//IO port----------------------------------------------------------------------/* Configure USART2 RTS and USART2 Tx as alternate function push-pull */GPIO_InitStructure.GPIO_Pin = GPIO_TxPin;//GPIO_RTSPin | GPIO_TxPin;GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;GPIO_Init(GPIOA, &GPIO_InitStructure);/* Configure USART2 CTS and USART2 Rx as input floating */GPIO_InitStructure.GPIO_Pin = GPIO_RxPin;//GPIO_CTSPin | GPIO_RxPin;GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;GPIO_Init(GPIOA, &GPIO_InitStructure);/* USART2 configuration ------------------------------------------------------*//* USART2 configured as follow:- BaudRate = 115200 baud - Word Length = 8 Bits- One Stop Bit- No parity- Hardware flow control enabled (RTS and CTS signals)- Receive and transmit enabled*/USART_InitStructure.USART_BaudRate = 115200;USART_InitStructure.USART_WordLength = USART_WordLength_8b;USART_InitStructure.USART_StopBits = USART_StopBits_1;USART_InitStructure.USART_Parity = USART_Parity_No ;USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;//USART_HardwareFlowControl_RTS_CTS;USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;USART_Init(USART2, &USART_InitStructure);/* Enable the USART2 */USART_Cmd(USART2, ENABLE);USART_ClearFlag(USART2, USART_FLAG_TC); // clear flag}/* --------------------------------------------------------------------------*// * @Brief: USART_sendBuf * * @Param: USARTx, which uart port* @Param: buf, send buffer* @Param: len, buffer length* * @Returns: send bytes count*//* --------------------------------------------------------------------------*/int USART_sendBuf(USART_TypeDef* USARTx, u8 *buf, u32 len){u32 busy_cnt = 0;u32 i = 0;while (i < len){USART_SendData(USARTx, buf[i++]);busy_cnt = 0;while(USART_GetFlagStatus(USARTx, USART_FLAG_TXE) == RESET){busy_cnt++; if (busy_cnt > 0xffff)return i; //send error, return sended bytes count}}return len; }/* --------------------------------------------------------------------------*// * @Brief: USART_recvBuf * * @Param: USARTx, which uart port* @Param: buf, receive buffer* @Param: len, buffer length* * @Returns: received bytes count*//* --------------------------------------------------------------------------*/int USART_recvBuf(USART_TypeDef* USARTx, u8 *buf, u32 len){u32 busy_cnt = 0;u32 i = 0;while (i < len){if(USART_GetFlagStatus(USARTx, USART_FLAG_RXNE) != RESET){buf[i] = USART_ReceiveData(USARTx) & 0xff;i++;}else{busy_cnt++;}if (busy_cnt > 0xffff)return i; //receive error, return received bytes count}return len;}
